EEPROM 95160 PDF

STMicroelectronics MW Series EEPROM are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for STMicroelectronics . Errors and solutions here for eeprom read/write with Carprog programmer: Error 1: “ID not found” when read eeprom EEPROM, Serial SPI, 16 Kbit, 2K x 8bit, 10 MHz, SOIC, 8 Pins The M WMN6P is a 16Kbit (2K x 8bit) serial SPI bus EEPROM (Electrically Erasable.

Author: Gardam Dogore
Country: Cape Verde
Language: English (Spanish)
Genre: Spiritual
Published (Last): 5 December 2011
Pages: 228
PDF File Size: 14.4 Mb
ePub File Size: 5.85 Mb
ISBN: 378-9-27252-195-7
Downloads: 99369
Price: Free* [*Free Regsitration Required]
Uploader: Diramar

Reply 1 ZLM Posts.

What is exact part number? Reply 2 benaknoun Spain Posts. Hi, thanks for your reply, here are the numbers on the chip: Reply 3 ZLM Posts. When you uploading the image, only use letter and number as file name. I think it should be SOIC8 mil chip.

Then the ADP should be used. Reply 4 benaknoun Spain Posts. Reply 5 ZLM Posts. It is SOIC8 mil chip. Use ToolA instead, because your chip pins already damaged. Reply 6 benaknoun Spain Posts. Reply 7 ZLM Posts. That is depending on your circuit design. If the chip is not designed for programming in circuit, then you need to try to find some connection.

  KWP2000 PROTOKOLL PDF

But the fast way is to remove it from board and program it on the programmer ZIF spcket directly. The wire can be any wires, as long as you can solder it. Reply 8 benaknoun Spain Posts.

Carprog 9.31 reads/writes eeprom 95160 with A4/A6 adapter

Reply 9 ZLM Posts. Reply 10 benaknoun Spain Posts. Hi, ok forget this chip, its damaged Chip is blank does this mean this chip is empty??? Reply 11 benaknoun Spain Posts.

Reply 12 ZLM Posts. I believe they will do the job.

Most of eeprlm on-board chips should have something. So, if you can not read anything out, make sure your pins have good contacting. That is safe and fastest way.

Reply 13 benaknoun Spain Posts. Hi, i have received the tools i bought from mcumall canada, there are numbers on the adapters, how do i know which pin is the right matching one with the chip? Reply 14 benaknoun Spain Posts. Hi, i have connected the tool to the chip 91560 adapter to the programmer. Device blank check failed at address: Also, when i click on ID, it says “function not supported on this device” Image Insert: Reply 15 ZLM Posts.

What is your chip on board?

MCUmall EPROM BIOS Chip Burner Forum – 8pin

Which part number you selected in software? If it is “”, then it has no ID on this chip.

  BULA BUSONID PDF

The “Device blank check failed ” means the chip is not a blank chip, there are some data in the chip. Try to power up the board and eepro, not connect pin 8 Vcc pin. All other pins are pin to pin connect to programmer socket. Reply 16 benaknoun Spain Posts. Hi, it ewprom i’m doing something right then! To be honest though, the other adapter i bought, not sure what its for??

Reply 17 ZLM Posts. You can save data as. It should be able to open it by same software. You need to find a way to test the data. The only way to test data is: What is your another adapter part number?

Reply 18 efprom Spain Posts. Also, another question please about the same chip: Reply 19 ZLM Posts. Once the chip is blank, then you can load your data file and click on Write button to wrtie the data into chip.

Author: admin