ASTM F2329 PDF

Zinc Coating Thickness Requirements: ASTM A vs. F Dimension. ASTM A ASTM F Avg. Coating. Thickness of. Specimens. Tested. ASTM F covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special. ASTM A does not cover threaded bolts and fasteners. ASTM A and F are the ASTM specifications that cover the requirements for.

Author: Samutilar Kagarg
Country: Czech Republic
Language: English (Spanish)
Genre: Career
Published (Last): 16 September 2017
Pages: 134
PDF File Size: 12.81 Mb
ePub File Size: 19.56 Mb
ISBN: 973-1-13117-689-2
Downloads: 63231
Price: Free* [*Free Regsitration Required]
Uploader: Akilar

Also in which material we are coating or galavanizing.

Afif — The difference between hot dip galvanizing structural articles and fasteners is the spinning. It is important to ensure the customer specifies which type of lot is required. According to Note C of Table 1, It is only required to conduct testing on samples for coating thickness once every five batch lots.

However, if a purchaser also requires f232 galvanizer to inspect dimensional requirements d2329 parts upon delivery, they must provide the galvanizer with the necessary tools and inspection gauges. The temperatures used in the hot-dip galvanizing process typically do not appreciably alter the mechanical properties of steel, but there are some instances when there are potential concerns. ASTM A This specification covers the requirements for hot-dip galvanizing on iron and steel products made from rolled pressed and forged shapes, castings, plates, bars, and strips.

Adhesion testing is not typically performed when galvanizing to the requirements of A unless there is evidence of an adhesion concern, f2239 F atm adhesion testing stout knife test to be performed for the number of articles listed in Table 1, and for every batch lot.

Hot-Dip Galvanizing Specifications

The type of production lot process will determine which column should be referenced for aztm sample size of each inspection criteria, as summarized in the table below, or per the F Sampling Plan Flow Chart.

  CHARTULARIUM UNIVERSITATIS PARISIENSIS PDF

Leave this field empty. Thus, the thickness determined is a point value. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Coating and Dimensional Requirements 8.

The dull appearance shall not be cause for rejection. I am having difficulty determining the hot dip zinc coating needed for an anchor bolt 60M 60mm and 1. The coating thickness requirements of A Table 1 meet or exceed those of F Table 2 except for:. See excerpt of Table 1 below. In addition, the purchaser shall provide fasteners having sufficient dimensional allowance to accommodate the zinc thickness deposition, as required in 8.

Dane- Thanks for response. Vinay- ASTM A and A both say that the maximum service temperature for galvanized bolts should not exceed F unless caution is used in regard to the potential for liquid hydrogen embirittlement.

The standard specification that covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special threaded fasteners applied by the hot-dip coating process. Suppliers shall furnish certified test results from which the shipping lots originated. Portland Bolt performs hot dip galvanizing of threaded fasteners within our 85, square foot manufacturing facility.

Many thanks Sal from Dubai. The method for testing the condition of adherence is speci?

ASTM F vs. ASTM A | American Galvanizer’s Association

Minor roughness that does not impair the intended use of the part, or roughness that is related to the uncoated surface condition of the part, shall not constitute grounds for rejection of the parts. NOTE 1—The scope of f239 speci? The information provided herein satm not intended as a representation or warranty on the part of the AGA.

ASTM A A covers galvanizing on many products including fasteners, while F is specific to threaded fasteners, nuts and washers. Will galvanizing bolts, that will be used for Sub-Sea hydratightightening using AquaMax jacks permissible, or would the stretching of the bolt under tension remove the galvanized warranty. Parts may be dull due to the presence of silicon in the steel. Beams and structural members are defined as steel products and are galvanized per A All the ASTM fastener standards refer to F for hot dip awtm, so that would be the most appropriate standard to reference.

  2N5457 DATASHEET PDF

Smoothness of a surface is a relative term.

ASTM F2329

Combining values from the two systems may result in non-conformance with the standard. It is the responsibility of the user of this standard to establish appropriate safety and health awtm and determine the applicability of regulatory limitations prior to use.

Furthermore, the qstm shall not be held responsible for any unanticipated distortion of parts. ASTM F describes two different sampling plans for batch lots and production lots. B For test method, see Could you please clarify?

Hot-Dip Galvanizing Specifications – Portland Bolt

The coating thickness requirements of A Table 1 meet or exceed those of F Table 2 except for: These instances can include when steel has been severely work hardened or when the galvanizing bath temperature exceeds the ast relief or tempering temperatures of the fasteners. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. In addition, small parts shall be air cooled as needed in order to prevent the formation of zinc oxide.

Otherwise, a third party will be required to apply the lubricant at an additional cost.

Author: admin